Author |
Topic: No spark (Read 510 times) |
|
mark_erdington
Newbie
I'm a YaBB newbie!
Posts: 28
|
I have just finished fitting new timming chains to my 2.9 24v cossie,come to start it and nothing.it turns over fine,but I have no spark.can anybody help 
|
|
 IP Logged |
|
|
|
Highlander
Moderator
Expert
13 Scorpios, XR4x4, Suzuki SJ413 for off road :)
Posts: 8244
|
 |
Re: No spark
« Reply #1 on: Aug 15th, 2006, 8:29pm » |
 Quote  Modify
|
throttle stuck open?
|
|
IP Logged |
on Oct 17th, 2011, 12:35pm, Simmo wrote:I give up !  Too much for an old boy! |
|
|
|
|
mark_erdington
Newbie
I'm a YaBB newbie!
Posts: 28
|
|
Re: No spark
« Reply #2 on: Aug 15th, 2006, 8:43pm » |
Quote Modify
|
No that works fine
|
|
IP Logged |
|
|
|
sector-9
Senior Member
No scorpio anymore
Posts: 1069
|
|
Re: No spark
« Reply #3 on: Aug 15th, 2006, 9:41pm » |
Quote Modify
|
Unlikely all three coils have died so check that you've reconnected all the wires to the battery, and that you haven't knocked the inertia cutout switch.
Darren
|
|
IP Logged |
|
|
|
hellblue
Full Member
Ill have silver,it dries just as fast !
Posts: 210
|
|
Re: No spark
« Reply #4 on: Aug 15th, 2006, 9:44pm » |
Quote Modify
|
If all is reconnected ok, hows the wiring loom? have a good look around cam & crank sensor wiring,coil & earth wires,& any other wiring you may have moved as you may well know these are prone to engine loom probs...
|
|
IP Logged |
Gary
|
|
|
howiedintheplace
Senior Member
Based near Evesham
Posts: 1194
|
|
Re: No spark
« Reply #5 on: Aug 15th, 2006, 10:08pm » |
Quote Modify
|
There is no easy answer here but first you need to look at what you have removed & refitted.
No.1 front pulley & crank sensor.
Are they fitted correctly as this is where the whole spark process starts.
|
|
IP Logged |
Dave
|
|
|
mark_erdington
Newbie
I'm a YaBB newbie!
Posts: 28
|
|
Re: No spark
« Reply #6 on: Aug 16th, 2006, 7:14pm » |
Quote Modify
|
Ive checked all conections and they look ok,but the cables are badly cracked,so how easy is it to change the loom between the V section,
|
|
IP Logged |
|
|
|
Dave
Senior Member
Tourmallard 24v (ex-owner)
Posts: 1984
|
|
Re: No spark
« Reply #7 on: Aug 17th, 2006, 5:52pm » |
Quote Modify
|
I reinsulated this loom, required the inlet manifolds removing but it wasn't too bad a job. Make sure that you check the crank sensor wiring as mine were touching each other due to failed insulation causing no spark.
|
|
IP Logged |
Life after the Scorpio ain't easy..
|
|
|
mark_erdington
Newbie
I'm a YaBB newbie!
Posts: 28
|
|
Re: No spark
« Reply #8 on: Aug 17th, 2006, 7:15pm » |
Quote Modify
|
ok Ive started to re wire the loom,
|
|
IP Logged |
|
|
|
|
Home
Help
Search
Members
Login
Reply
Send Topic
Print